#E3 ODE PRO INSTALLATION TUTORIAL INSTALL#
#E3 ODE PRO INSTALLATION TUTORIAL CODE#
#E3 ODE PRO INSTALLATION TUTORIAL PS3#

You need to check again how is connected the PSU, specially the wire with small white connectorsДЄnd if you filp it (hard to do because it has a mark to avoid this) you could fry some component but my bet is it should enter in standby (red led turned on).

#E3 ODE PRO INSTALLATION TUTORIAL PS3#

I have no idea what does the PS3 if you try to boot it without them.

you need to find the original value from factory, buy a replacement (or recycle them from some crappy circuit board you have in yoiur junkyard), and solder them back in his place So one of the first things you need to do is to search about this resitors. because whoever installed the ODE for you throw them out of the window if you want to remove the ODE you need to solder back that resistorsДЄnd probably you dont have the resitors. this 2 wires are the ones that are doing 'the magic'

#E3 ODE PRO INSTALLATION TUTORIAL INSTALL#

Im not very used to ODE, i never cared much so i never was interested in the installations or what hapens when you try to update to a non supported firmwareД«ut to install the ODE are needed (as far i remember) to remove 2 resistors from the motherboard, where you need to connect 2 wires. maybe you bought the PS3 used, and is made of parts from other models, the case (with the sticker) could be CECH42xxB. So most probably you have a CECH-42xxA (is printed in the sticker outside of the case btw)ДЄnyway. The 'A' is the internal storage capacity of size 'small' (and 'B' is medium, and 'C' is big). this is the region and doesnt have any importance, doesnt matters The first thing that made me doubt is the PS3 with 12gb eMMC flash are the ones who ends in -> A Sometimes is needed to tell the accurate exact info when you are asking for help, it can be anything, starting with the PS3 model, everything you did, and even if you used some firmware function you need to tell how is named and the messages you saw on screen PSU or some missing voltage), but lets restarts again :P uses to be an indication that is suffering a general problem that affects the whole device (a.k.a. Sometimes not doing anything is a good signal btw. I think getting power is more important right now than erasing the hdd.Also i checked for the piece too much similar pieces which were made by samsung i can take a photo of the whole motherboard if neededД¬lick to expand.It has been your biggest problem since beginning the other day when you said it was lighting the green led then shutting down, now is even worst because it doest makes any led activity I wont bring to repair so i am ready to try all sorts of things to try to save it. Note:The PS3 received power even without the Blueray drive i tried with and without still same thing? Ok rip i killed my ps3 hard.So here is all what i did help appreciated.Дў.Tried to update to 4.82 to install han went into a boot install failed loopДЈ.Opened the playstation 3 in a hope to find a hard drive failed.Д¤.After reassembling it gave a red light and turned off 1 sec after i pressed on.ДҐ.Redissasembled it and also decided to remove the E3 ODE PRO.Д¦.Removed the solder board from motherboard,some cables attached to usb port 0 and the top one with all of its cables.Д§.Reconnected wlan,bluetooth,power near fan,button to power on and power supply slot.ДЁ.PS3 doesnt even receives power no red light totally dead. This will probably give you a better idea of where to go from there. I know this isn't a definite answer, but I hope it helps.ДЇirst place I would start is with searching for what the color/amount of blinks the light is communicating.

The safest way to disassemble and reassemble your console is to start on youtube.ДЇind a tutorial video that you can follow along to, that has good credibility and comments.ДЄlways try to memorize or write down in order what you are unscrewing or taking apart, and when finished, go back through the list and assemble it in the reverse order. I suggest opening it back up first, find some pictures of how the Super Slim should look on the inside, and check all connections/slots that you can find, disconnect, then reconnecting them to make sure they have a secure fit.ДЄlso, make sure that wherever you decide to open up your console, that static electricity can't build up on you. I've had a few similar experiences with my consoles after disassembling them, and it may in fact be something as simple as forgetting to reconnect one of the cords back to its correct slot.

#E3 ODE PRO INSTALLATION TUTORIAL CODE#

If the Playstation3 is blinking a certain amount of lights of a certain color, that's the systems way of communicating an error code that you can then search online to find out what sort of error is occuring in the console. The innards of a SS model is probably different, yet certain components are probably similar. I personally haven't disassembled a Super Slime PS3, but have Fats and Slims.

E3 ode pro installation tutorial